1 GAL. Armor WB25 Water Based High Gloss Acrylic Cure and Seal for New & Existin

Description

Can be used on new, uncured concrete to help aid with proper curing
Meets ASTM C1315 and ASTM C309 standards
Will enhance dull and faded surfaces with a high gloss finish
Will reduce damage caused by water absorption and surface abrasion
UV resistant, non-yellowing, breathable
Also great for fully cured concrete and concrete pavers
Product Description
Water-Based High Gloss Wet Look Sealer
For New and Existing Concrete, and Concrete Pavers
The Armor WB25 is a water based acrylic high gloss sealer that is designed to seal, enhance, and protect a variety of exterior concrete and concrete paver surfaces. It penetrates deep into the surface where it chemically bonds to the pores of the concrete and pavers, creating a long lasting, non-yellowing, breathable finish that enhances dull or faded surfaces. The Armor WB25 is ASTM tested and approved as a cure and seal, and can be applied to new concrete to help with proper curing.
Uses
Uses
:
The Armor WB25 is designed for use on poured concrete, stamped concrete, aggregate concrete, and concrete paver surfaces. It can be applied to unsealed surfaces, and surfaces previously sealed with a solvent-based acrylic. It can be applied to new concrete to help with proper curing. It is a great choice for driveways, walkways, patios, concrete floors, pool decks, and more!
Do not apply this product to red clay brick, slate, flagstone, or other types of natural stone. If you are looking to seal red clay brick, slate, flagstone, or any other type of natural stone, consider the Armor WL550 or the Armor SX5000 WB.
BENEFITS
Provides a Lasting Wet Look
When properly applied, the Armor WB25 can last for up to 1-3 years before the need for a recoat.
Won't Peel, Flake, or Yellow
The Armor WB25 is breathable, UV-resistant, and non-yellowing. It is self-priming and offers a superior bond to concrete and concrete pavers.
Protects The Surface
The durable high gloss surface film will reduce damage caused by surface abrasion, spills, water absorption, road salts, and weather.
Can Be Applied To New Concrete
The Armor WB25 meets ASTM C1315 and ASTM C309 standards, and can be applied to new concrete to help with the curing process.
High Gloss Finish
Appearance
When applied in clear, the Armor WB25 will slightly enhance the natural coloring the concrete or pavers, and seal it with a transparent high gloss finish.
The actual level of gloss and enhancement received will depend on the type and age of the surface, age, porosity, condition, applicator, application method, and amount of material applied. For an accurate representation of what your surface will look like once sealed, we suggest applying the product to a test area first.
How To Apply
The Armor WB25 can be applied with a 3/8-1/2” nap roller, or a commercial pump sprayer. For a consistent high gloss finish, apply two coats spaced 6-8 hours apart. Do not exceed 24 hours apart between coats.
Time Of Day:
The Armor WB25 should only be applied in the early evening when air and surface temperatures are declining, and when the sun is no longer positioned over the surface.
Surface Preparation:
The Armor WB25 should be applied to a completely clean and dry surface. If the surface was cleaned with water or pressure washed prior to application, allow the surface to dry for at least 24 hours before sealing. While the surface may appear dry and feel dry to touch, water below the surface trapped in the pores can cause the issues. While pressure washing the surface is typically sufficient, spot treatment may be necessary for deep or older stains.
The Armor WB25 is designed specifically to be used on unsealed porous concrete and concrete pavers. It can also be applied to concrete and concrete paver surfaces previously sealed with a water based acrylic as long as the acrylic has been properly prepped for adhesion. The Armor WB25 should not be used on smooth or dense concrete surfaces. It is always suggested to apply the Armor WB25 to a test area to verify absorption, coverage, compatibility, and project suitability.
The Armor WB25 should not be used to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone. If you are looking to seal clay brick, red Chicago pavers, flagstone, slate, or natural stone, consider instead of the Armor WL550 or the Armor SX5000 WB.
Note About Sealing Concrete Pavers: Please note, while the Armor WB25 can be applied over paver joints, it is not designed as a bonding agent and will not harden or bond the loose sand in the paver joints. If applying with a roller, loose sand in the joints may cling to the roller and be redistributed across the pavers. For best results, apply first coat with a sprayer if you are applying to pavers with loose sand in the paver joints.
When applying to porous pavers, gloss level may be reduced, and more material may be required to achieve desired finish.
Adding Non-Slip: For added surface traction, the Armor Non-Slip additive can be added. The ultra-fine and fine Armor Non-Slip additives works best in the Armor WB25. Applying the Ultra-Fine: Slowly drill mix 3-6.5 ounces of non-slip additive per gallon of sealer, until completely blended, then apply. For Fine: When applying the second coat, add the non-slip additive to the coating using a broadcast spreader, and back roll to encapsulate the non-slip additive.
Clean-Up:
Use warm water and soap. Dispose of containers in accordance with local and federal regulations.
Removal:
Dried, cured sealer may be removed with the Armor CR100, or by using a diamond grinding method, sandblasting method or similar mechanical action.
Up to 175 FT2/Gallon In One Coat
Coverage
Porous Surfaces: Up to 175 FT2/gallon in one coat.
Smooth Surfaces (once properly prepped): Up to 200-225 FT2/gallon in one coat.
Coverage will vary depending on porosity, surface condition, application method, and the amount of material applied by the applicator. The above coverage rates are estimates and will vary. Two coats are suggested for even coverage and appearance. Please note, if it is your first time sealing pavers, or an overly porous surface, a third coat may be required.
More Great Foundation Armor Products To Consider
Add to Cart
Add to Cart
Add to Cart
Add to Cart
Add to Cart
Add to Cart
Customer Reviews
4.6 out of 5 stars
54
4.6 out of 5 stars
2,056
4.2 out of 5 stars
24
4.5 out of 5 stars
833
4.4 out of 5 stars
419
4.7 out of 5 stars
10
4.0 out of 5 stars
8
Price
9.99
$
199
.
99
4.99
$
224
.
99
4.99
$
224
.
99
4.99
$
224
.
99
9.99
$
249
.
99
—
9.99
$
169
.
99
Uses
Concrete/Pavers
Concrete/Pavers
Concrete/Pavers
Concrete/Pavers
Concrete/Pavers/Brick/Stone
For Sealers/Coatings/Paint
For Sealers/Coatings/Cleaner
Leaves Visible Surface Film
✔
✔
✔
✔
✘
✘
✘
Finish
High Gloss
Low Gloss
High Gloss
High Gloss
Matte Wet Look
N/A
N/A
Base
Water-Based
Solvent-Based
Solvent-Based
Solvent-Based
Solvent-Based
N/A
N/A
Chemical Type
Acrylic
Acrylic
Acrylic
Acrylic
Hybrid
N/A
N/A
Life
Up To 1-3 Years
Up To 1-3 Years
Up To 1-3 Years
Up To 1-3 Years
Up to 3-5 YEars
N/A
N/A
Provides Wet Look
✘
✔
✔
✔
✔
✘
✘
Cure and Seal
✔
✘
✔
✘
✘
✘
✘